CCGT 060204-AS IC20
Image match unverified- Item / entry
- Catalogue entry
- Grade
- IC20
- Edge material
- Carbide
- Stated use
- Aluminum machining
Specification · manufacturer examples available
CCGT 060204
80° rhombic · 7° clearance · CCGT series
Inscribed circle · IC6.35 mm
Thickness · S2.38 mm
Corner radius · R0.4 mm
Product grade and application depend on the full manufacturer designation. Confirm the holder pocket and clamping before choosing a replacement.
← Browse CCGT specificationsCCGT 060204Nominal geometry
IC 6.35S 2.38R 0.4mm
Nominal dimensions
Dimension referenceCode-table source ↗
Swipe to see the full dimension drawing →
| Property | Value | Basis |
|---|---|---|
| Inscribed circle / IC | 6.35 mm | Linked product dimensions |
| Thickness / S | 2.38 mm | Linked product dimensions |
| Corner radius / RE | 0.4 mm | Linked product dimensions |
| Basic shape / clearance | 80° rhombic / 7° | CCGT designation |
| Product tolerances | Consult product drawing | Not independently reviewed here |
These are nominal reference dimensions. Hole profile, edge construction and usable edges may differ between products.
A meaningful comparison
What changes from 060202?
The radius increases from 0.2 to 0.4 mm while the nominal inscribed circle and thickness stay the same. This is a geometric comparison, not an interchangeability decision.
Swipe to compare both sizes →
| Property | CCGT 060204 ↗ | CCGT 060202 ↗ |
|---|---|---|
| Corner radiusDifferent | 0.4 mm | 0.2 mm |
| Inscribed circle | 6.35 mm | 6.35 mm |
| Thickness | 2.38 mm | 2.38 mm |
| Corner angle | 80 ° | 80 ° |
| Clearance angle | 7 ° | 7 ° |
| Family | CCGT | CCGT |
Before choosing this radius
Check the corner required by the drawing and the stability of the setup before moving to a larger radius. Confirm the complete insert and holder specification.
From a size to an actual product
Documented product examples
The application belongs to the full product below. These examples are not a recommendation or a stock listing.
CCGT 060204-SF RTC+
Image match unverified- Item / entry
- 1771692
- Grade
- RTC+
- Edge material
- PVD-coated cermet
- Stated use
- Continuous finishing of steel and stainless steel
Does matching geometry mean I can swap these inserts?
No. Confirm the holder pocket, clamping, insert tolerances, cutting direction and complete product specification. Check grade, chipbreaker and application data for the actual workpiece and setup.
Read the base designation
CShape
CClearance
GTolerance
TConfiguration
06Size
02Thickness
04Radius
The code identifies a base geometry. Suffixes such as AS, SF, F, IC20, RTC+ or ID4 belong to a manufacturer’s product system.
Evidence, in context
Sources & review scope
Reviewed 2026-10-19. A checked field is not a product certification.
ISCAR · Aluminum Machining (opens in a new tab)
Printed page 17 / PDF page 19, CCGT-AS table
What this source supports
IC, thickness and radius for 060201-AS, 060202-AS and 060204-AS; IC20 grade and aluminum application. Catalogue edition not identified.
Rinaldi · CCGT-SF RTC+ (opens in a new tab)
Dimensions and item-number table
What this source supports
Dimensions and item numbers for 060202-SF RTC+ and 060204-SF RTC+; grade and stated application. Cutting-data rows are not used because the page repeats a size label.
Inch values are calculated from the listed millimetre values ÷ 25.4, rounded to four decimals. Product tolerances, compatibility and cutting performance require the applicable product specification.