refmanualEngineering, within reach.

Specification · manufacturer examples available

CCGT 060201

80° rhombic · 7° clearance · CCGT series

Inscribed circle · IC6.35 mm
Thickness · S2.38 mm
Corner radius · R0.1 mm
Dimension drawing ↓
Compare with CCGT 060202 →View manufacturer examples ↓

Product grade and application depend on the full manufacturer designation. Confirm the holder pocket and clamping before choosing a replacement.

← Browse CCGT specifications
CCGT 060201Nominal geometry
80° rhombic 7° clearance · T configuration STRUCTURE ONLY
IC 6.35S 2.38R 0.1mm
Hole + one-face countersink · 1-face chipbreaker in base type. Outer envelope follows nominal IC, thickness and cutting-corner radius. Dashed circles are mounting symbols, not bore dimensions. Chipbreaker, edge preparation, tip construction and coating are not depicted. This is not a product photograph.

Nominal dimensions

Dimension referenceCode-table source ↗

Swipe to see the full dimension drawing →

01 / TOP VIEW IC 6.35 mm Dashed green circle = inscribed circle Dashed gray circles = mounting symbol only 02 / SIDE-NORMAL SECTION S 2.38 mm 7° flank from vertical 03 / CUTTING CORNER · ENLARGED R 0.1 mm · 80°
Separate scales for the three views. S is measured between the top and bottom reference planes. The side section shows the outer envelope only. Minor corners, bore/countersink dimensions, chipbreaker and edge preparation require the exact manufacturer drawing.
PropertyValueBasis
Inscribed circle / IC6.35 mmLinked product dimensions
Thickness / S2.38 mmLinked product dimensions
Corner radius / RE0.1 mmLinked product dimensions
Basic shape / clearance80° rhombic / 7°CCGT designation
Product tolerancesConsult product drawingNot independently reviewed here

These are nominal reference dimensions. Hole profile, edge construction and usable edges may differ between products.

A meaningful comparison

What changes from 060202?

A 0.1 mm corner radius, half the radius of 060202. The nominal inscribed circle and thickness stay the same.

Swipe to compare both sizes →

Nominal insert dimensions (millimetres)
PropertyCCGT 060201 ↗CCGT 060202 ↗
Corner radiusDifferent0.1 mm0.2 mm
Inscribed circle6.35 mm6.35 mm
Thickness2.38 mm2.38 mm
Corner angle80 °80 °
Clearance angle7 °7 °
FamilyCCGT CCGT
Before choosing this radius

Check the edge preparation and the product’s minimum feed and depth of cut. A small nominal radius alone does not establish suitability for a delicate cut.

How to assess nose radius →Browse the complete CCGT family →

From a size to an actual product

Documented product examples

The application belongs to the full product below. These examples are not a recommendation or a stock listing.

Does matching geometry mean I can swap these inserts?

No. Confirm the holder pocket, clamping, insert tolerances, cutting direction and complete product specification. Check grade, chipbreaker and application data for the actual workpiece and setup.

Read the base designation

CShape
CClearance
GTolerance
TConfiguration
06Size
02Thickness
01Radius

The code identifies a base geometry. Suffixes such as AS, SF, F, IC20, RTC+ or ID4 belong to a manufacturer’s product system.

Read the full designation guide →

Evidence, in context

Sources & review scope

Reviewed 2026-10-19. A checked field is not a product certification.

ISCAR · Aluminum Machining (opens in a new tab)

Printed page 17 / PDF page 19, CCGT-AS table

What this source supports

IC, thickness and radius for 060201-AS, 060202-AS and 060204-AS; IC20 grade and aluminum application. Catalogue edition not identified.

Inch values are calculated from the listed millimetre values ÷ 25.4, rounded to four decimals. Product tolerances, compatibility and cutting performance require the applicable product specification.