refmanualEngineering, within reach.

Specification reference · product not verified

WNMG 060408

Trigon · 0° clearance · WNMG series

Inscribed circle · IC9.525 mm
Thickness · S4.76 mm
Corner radius · R0.8 mm
Dimension drawing ↓
Compare with WNMG 060404 →Check product information ↓

No exact manufacturer product is documented for this specification. Confirm the holder pocket and clamping before choosing a replacement.

← Browse WNMG specifications
WNMG 060408Nominal geometry
Trigon 0° clearance · G configuration STRUCTURE ONLY
IC 9.525S 4.76R 0.8mm
Cylindrical hole · 2-face chipbreaker in base type. Outer envelope follows nominal IC, thickness and cutting-corner radius. Dashed circles are mounting symbols, not bore dimensions. Chipbreaker, edge preparation, tip construction and coating are not depicted. This is not a product photograph.

Nominal code dimensions

Dimension referenceCode-table source ↗

Swipe to see the full dimension drawing →

01 / TOP VIEW IC 9.525 mm Dashed green circle = inscribed circle Dashed gray circles = mounting symbol only 02 / SIDE-NORMAL SECTION S 4.76 mm 0° flank from vertical 03 / CUTTING CORNER · ENLARGED R 0.8 mm · 80°
Separate scales for the three views. S is measured between the top and bottom reference planes. The side section shows the outer envelope only. Minor corners, bore/countersink dimensions, chipbreaker and edge preparation require the exact manufacturer drawing.
FieldmminCode-table position
Inscribed circle9.5250.37505 · ISCAR metric table ↗
Thickness4.760.18746 · ISCAR metric table ↗
Corner radius0.80.03157 · ISCAR metric table ↗

The inch column is mm ÷ 25.4, rounded to four decimal places. This is not an ANSI designation conversion. Product tolerances and clamping dimensions are not inferred.

WNMG 060408 versus WNMG 060404

radius: 0.4 → 0.8 mm. The nominal IC and thickness are unchanged.

Swipe to compare both references →

Nominal code-reference comparison
PropertyWNMG 060408WNMG 060404
FamilyWNMG WNMG
OutlineTrigon Trigon
Corner radius0.8 mm0.4 mm
Inscribed circle9.525 mm9.525 mm
Thickness4.76 mm4.76 mm
Corner angle80 °80 °
Clearance angle0 °0 °
Tolerance symbolM M
Configuration symbolG G
EvidenceCode table; product example not documentedCode table; product example not documented

Where this radius sits

The WNMG 0604 group in this directory has 3 entries, from 0.4 to 1.2 mm radius. This sits between the smallest and largest listed radii.

Confirm the part contour and tool compensation for 0.8 mm. A radius change does not establish surface finish, cutting data or holder compatibility.

Nearby WNMG references

  • WNMG 060404 → — radius: 0.8 → 0.4 mm. The nominal IC and thickness are unchanged.
  • WNMG 060412 → — radius: 0.8 → 1.2 mm. The nominal IC and thickness are unchanged.
  • WNMG 060208 → — thickness: 4.76 → 2.38 mm. The nominal seat envelope changes; holder fit must be rechecked.

Product evidence for WNMG 060408

No exact product row is attached to WNMG 060408. The WNMG code and 060408 digits describe nominal geometry; they do not prove that a product is manufactured or available.

Compare the documented evidence within WNMG →

Read shared WNMG configuration and selection limits →Calculate speed or feed after obtaining cutting data →

Source and limits

ISCAR · Metric insert identification ↗ · Single-sheet PDF, sections 1, 2, 4, 5, 6 and 7; visually checked 2026-10-20.

Shape, clearance, configuration and nominal code tables only. No grade, usable-edge count, catalogue availability or acceptance tolerances inferred. Values labeled “code table” are interpretations of a designation, not measurements of a delivered product. Product-row values are reported separately, including differences in printed precision.

See the page-by-page review →