refmanualEngineering, within reach.

Specification reference · product not verified

TNMM 16T316

Triangular · 0° clearance · TNMM series

Inscribed circle · IC9.525 mm
Thickness · S3.97 mm
Corner radius · R1.6 mm
Dimension drawing ↓
Compare with TNMM 16T312 →Check product information ↓

No exact manufacturer product is documented for this specification. Confirm the holder pocket and clamping before choosing a replacement.

← Browse TNMM specifications
TNMM 16T316Nominal geometry
Triangular 0° clearance · M configuration STRUCTURE ONLY
IC 9.525S 3.97R 1.6mm
Cylindrical hole · 1-face chipbreaker in base type. Outer envelope follows nominal IC, thickness and cutting-corner radius. Dashed circles are mounting symbols, not bore dimensions. Chipbreaker, edge preparation, tip construction and coating are not depicted. This is not a product photograph.

Nominal code dimensions

Dimension referenceCode-table source ↗

Swipe to see the full dimension drawing →

01 / TOP VIEW IC 9.525 mm Dashed green circle = inscribed circle Dashed gray circles = mounting symbol only 02 / SIDE-NORMAL SECTION S 3.97 mm 0° flank from vertical 03 / CUTTING CORNER · ENLARGED R 1.6 mm · 60°
Separate scales for the three views. S is measured between the top and bottom reference planes. The side section shows the outer envelope only. Minor corners, bore/countersink dimensions, chipbreaker and edge preparation require the exact manufacturer drawing.
FieldmminCode-table position
Inscribed circle9.5250.37505 · ISCAR metric table ↗
Thickness3.970.15636 · ISCAR metric table ↗
Corner radius1.60.06307 · ISCAR metric table ↗

The inch column is mm ÷ 25.4, rounded to four decimal places. This is not an ANSI designation conversion. Product tolerances and clamping dimensions are not inferred.

TNMM 16T316 versus TNMM 16T312

radius: 1.2 → 1.6 mm. The nominal IC and thickness are unchanged.

Swipe to compare both references →

Nominal code-reference comparison
PropertyTNMM 16T316TNMM 16T312
FamilyTNMM TNMM
OutlineTriangular Triangular
Corner radius1.6 mm1.2 mm
Inscribed circle9.525 mm9.525 mm
Thickness3.97 mm3.97 mm
Corner angle60 °60 °
Clearance angle0 °0 °
Tolerance symbolM M
Configuration symbolM M
EvidenceCode table; product example not documentedCode table; product example not documented

Where this radius sits

The TNMM 16T3 group in this directory has 4 entries, from 0.4 to 1.6 mm radius. This is the largest listed radius in that group.

Confirm the part contour and tool compensation for 1.6 mm. A radius change does not establish surface finish, cutting data or holder compatibility.

Nearby TNMM references

  • TNMM 16T312 → — radius: 1.6 → 1.2 mm. The nominal IC and thickness are unchanged.
  • TNMM 16T308 → — radius: 1.6 → 0.8 mm. The nominal IC and thickness are unchanged.
  • TNMM 16T304 → — radius: 1.6 → 0.4 mm. The nominal IC and thickness are unchanged.

Product evidence for TNMM 16T316

No exact product row is attached to TNMM 16T316. The TNMM code and 16T316 digits describe nominal geometry; they do not prove that a product is manufactured or available.

Compare the documented evidence within TNMM →

Read shared TNMM configuration and selection limits →Calculate speed or feed after obtaining cutting data →

Source and limits

ISCAR · Metric insert identification ↗ · Single-sheet PDF, sections 1, 2, 4, 5, 6 and 7; visually checked 2026-10-20.

Shape, clearance, configuration and nominal code tables only. No grade, usable-edge count, catalogue availability or acceptance tolerances inferred. Values labeled “code table” are interpretations of a designation, not measurements of a delivered product. Product-row values are reported separately, including differences in printed precision.

See the page-by-page review →