Specification · manufacturer examples available

DNMG 150408

55° rhombic · 0° clearance · DNMG series

Inscribed circle · IC12.7 mm

Thickness · S4.76 mm

Corner radius · R0.8 mm

Compare with DNMG 150404 →View manufacturer examples ↓

Product grade and application depend on the full manufacturer designation. Confirm the holder pocket and clamping before choosing a replacement.

← Browse DNMG specifications

DNMG 150408Nominal geometry

IC 12.7S 4.76R 0.8mm

Cylindrical hole · 2-face chipbreaker in base type. Outer envelope follows nominal IC, thickness and cutting-corner radius. Dashed circles are mounting symbols, not bore dimensions. Chipbreaker, edge preparation, tip construction and coating are not depicted. This is not a product photograph.

Nominal code dimensions

Dimension referenceCode-table source ↗

Swipe to see the full dimension drawing →

Separate scales for the three views. S is measured between the top and bottom reference planes. The side section shows the outer envelope only. Minor corners, bore/countersink dimensions, chipbreaker and edge preparation require the exact manufacturer drawing.

Field	mm	in	Code-table position
Inscribed circle	12.7	0.5000	5 · ISCAR metric table ↗
Thickness	4.76	0.1874	6 · ISCAR metric table ↗
Corner radius	0.8	0.0315	7 · ISCAR metric table ↗

The inch column is mm ÷ 25.4, rounded to four decimal places. This is not an ANSI designation conversion. Product tolerances and clamping dimensions are not inferred.

DNMG 150408 versus DNMG 150404

radius: 0.4 → 0.8 mm. The nominal IC and thickness are unchanged.

Swipe to compare both references →

Nominal code-reference comparison
Property	DNMG 150408	DNMG 150404
Family	DNMG	DNMG
Outline	55° rhombic	55° rhombic
Corner radius	0.8 mm	0.4 mm
Inscribed circle	12.7 mm	12.7 mm
Thickness	4.76 mm	4.76 mm
Corner angle	55 °	55 °
Clearance angle	0 °	0 °
Tolerance symbol	M	M
Configuration symbol	G	G
Evidence	Code table + 2 catalogue examples	Code table + 1 catalogue examples

Where this radius sits

The DNMG 1504 group in this directory has 4 entries, from 0.4 to 1.6 mm radius. This sits between the smallest and largest listed radii.

Confirm the part contour and tool compensation for 0.8 mm. A radius change does not establish surface finish, cutting data or holder compatibility.

Nearby DNMG references

DNMG 150404 → — radius: 0.8 → 0.4 mm. The nominal IC and thickness are unchanged.
DNMG 150412 → — radius: 0.8 → 1.2 mm. The nominal IC and thickness are unchanged.
DNMG 150416 → — radius: 0.8 → 1.6 mm. The nominal IC and thickness are unchanged.

Product evidence for DNMG 150408

ISCAR / catalogue example

DNMG 150408-TF IC20

IC: 12.7 mm
Thickness: 4.76 mm
Radius: 0.8 mm
Grade: IC20

Read the exact catalogue row ↗

Aluminum Machining, PDF page 12 / printed page 10, exact designation row. Exact geometry row and IC20 availability mark in this catalogue. Cutting conditions require the applicable product data; no stock check.

ISCAR / catalogue example

DNMG 150408-PP

IC: 12.7 mm
Thickness: 4.76 mm
Radius: 0.8 mm
Grade: Select in the original product table

Read the exact catalogue row ↗

Aluminum Machining, PDF page 13 / printed page 11, exact designation row. Catalogue geometry row. Grade and cutting conditions must be read for the chosen product; no stock check.

Read shared DNMG configuration and selection limits →Calculate speed or feed after obtaining cutting data →

Documented applications for DNMG 150408

DNMG150408-SM T6215

Source image only · representative family image

Tungaloy · case-study

IC / thickness / radius: 12.7 / 4.76 / 0.8 mm
Material scope: stainless

stainless / external / medium

Check this complete product and its conditions →

Tungaloy T6200/AH6200 applications ↗ · Named practical examples and SF/SM/SH stage table.

Tungaloy metric catalogue 547 ↗ · Printed page 10; exact product row and grade/geometry application matrix.

SUS304 wet external-turning case; continuity supported at grade level. Application evidence is attached to this full product, not every insert sharing the base code.

Source and limits

ISCAR · Metric insert identification ↗ · Single-sheet PDF, sections 1, 2, 4, 5, 6 and 7; visually checked 2026-10-20.

Shape, clearance, configuration and nominal code tables only. No grade, usable-edge count, catalogue availability or acceptance tolerances inferred. Values labeled “code table” are interpretations of a designation, not measurements of a delivered product. Product-row values are reported separately, including differences in printed precision.

See the page-by-page review →